Natural as wood…

Austrian traditions of wood treatment


Safety
and Effectiveness
head

Harmony of house and nature

Interior oil-lasur for wood No.1020

 

Combination of oils and resins for surface hardening and its protection from moisture and dirt. Applying is easy; polishing is not required. Natural look of wood.

Use
Combination of oils and resins for surface hardening and its protection from moisture and dirt. Applying is easy; polishing is not required. Natural look of wood.
Technical data sheet — PDF
Properties Directions for use
Gloss: Silky-mat (after polishing).
Color: In its liquid form, the compound is milky-white and after drying up it is transparent. After several months the wood gains nice honey-like tincture. The compound can be colored with dry pigments, aqueous or universal coloring pastes.
Complete composition: water; heat-polymerized mixture of linseed oil and wood oil; boiled down mixture of linseed oil, castor oil, wood oil, resin of conifers and glycerin from vegetable sources; vegetable wetting agents; lecithin; natural silver in ultra-micro-dispersed form (nanoform); fast-drying materials based on cobalt (less than 0.01%) and manganese (less than 0.01%).
Content of artificial substances: The compound contains two artificial substances: they are fast-drying materials (siccatives) based on cobalt and manganese. The compound contains neither conserving agents nor siccatives based on lead, barium or other dangerous heavy metals and other artificial substances.
Thinning agent: Water.
Solids content: <100%.
Storage: It is supposed to be stored in a dry cool place in tightly closed packing under temperature not lower than +5°С and preferably not higher than +35°С. Do not freeze!
Shelf life: Storage term in the original closed container is about 12 months.
Container volume: 0.5; 1; 2.5 and 10 l.
Class of hazard: Not applicable.
Density: 0.99 to 1.02 g/cm3.
Viscosity: ~25 to 30 sec (DIN-size beaker 4 mm).
Flash-point: Do not apply at more than 200°C.
Quantity used: Approximately 10 to 15 m2/l for the first layer, 12 to 20 m2/l for the second layer and 30 to 35 m2/l for the third layer depending on absorptiveness of the surface.
Drying time: Approximately in 6 to 8 hours it is possible to apply the next layer; in 12 to 24 hours after application process the last layer, the surface can be slightly polished. Final drying up takes 24 to 48 hours at temperature 20°C and humidity 50-60%.
Surface preparatio: Remove an old film coat (if any). Clean the surface from dirt and grease (by washing up with water and soap) and dry up to the humidity level 14-15%. In dependence with wood kind and desirable smoothness, grind off the surface with abrasive means with grain P100-220 (it is recommended in average not less than P150-180), remove dust thoroughly.
Application process: The surface must be dry; the recommended humidity is not more than 14 or 15%. It is recommended to conduct the treatment at temperature not less than +12 to +15°С. Mix the compound properly and apply it on the surface with a brush, a roller with short nap or a spray gun along grain. In 6 to 8 hours, the raised nap can be removed by a sandpaper sheet with grain P240. The second layer should be applied in the similar way. If necessary, in 6 to 8 hours, application process of the third layer is possible.Final drying up will take place in 24 to 48 hours.Above the final layer, not earlier than in 3 days, the layer of Carnauba wax, high gloss No.1090 can by apply.
Tinting: Into the compound, dry pigments can be added in volume up to 30% or universal pastes or aqueous coloring pastes in volume recommended by a paste producer. For uniform mixing up it is recommended first to dilute a pigment in a small compound volume and then to mix up with the rest of compound.
Cleaning and care: The surface can be wiped with a wet tissue. In a case of contamination, wash it up with warm water with soap. If the surface is worn-out, apply a compound thin layer on the worn-out field. In a case of a local damage (or contamination), the surface should be scraped with a sandpaper with small grain (for example P240) and then the treated field should be covered with the compound. For a better gloss and renovation above all, the compound No.1010 can be apply according to the instruction.For better conservation of the silky gloss and fresh look of the surface, it is recommended wetting cleaning, namely wiping the surface with water, to 10 liters of which 1 or 2 tablespoons of the compound No.1010 or emulsion of carnauba palm wax No.1090 should be added.
Tool cleaning: Immediately after use it is needed to wash the tool with warm water with soap or detergent and to dry it up.
Utilization: An empty container must be utilized in accordance with regional legislation. Any dried up product remainders can be disposed together with domestic garbage.
Safety advice: To store in a childproof place. It is forbidden to pour remainders into sewage. In a case of contact with eyes, wash with a lot of water. Soaked with the product materials (tissues, dresses, sponges) and tools must be washed up with water and soap and dried up in a fireproof container or on a fireproof surface as during the drying up process, a hazard is present of a spontaneous combustion. After that the materials can be disposed together with common garbage.

The compound contains completely natural substances. That is why before its application it is necessary to ensure that you do not suffer from allergy to vegetable substances and products of beekeeping!