Natural as wood…

Austrian traditions of wood treatment


Environment
Friendliness and Care

Protection and nature power

Terrace oil No.3050

For floors, handrails and other elements of terraces, patios, arbors, porches, etc. Product with dry remainder 100%. Short drying up time. High wear resistance.

Use
It is meant for floors, handrails, terraces, outdoor concert platforms and constructive elements subjected to a high wear in conditions of atmospheric factors action
Technical data sheet — PDF
Properties Directions for use
Gloss: Silky-semi-glazed.
Color: Pale-strawy (natural). After several months the wood gets a nice honey-like tincture. The compound can be colored with dry pigments. For external treatment, it is needed to use the compound only it its colored form. It is recommended using mineral pigments.
Complete composition: heat-polymerized mixture of linseed oil and wood oil; boiled down mixture of linseed oil, castor oil, wood oil, conifer resin, glycerin and fatty acids from vegetable sources; heat-polymerized castor oil; heat-polymerized linseed oil; heat-polymerized wood oil; wood oil; zinc oxide; fir needle oil; fast-drying materials based on cobalt (less than 0.01%) and manganese (less than 0.01%).
Content of artificial substances: The compound contains two artificial substances: they are fast-drying materials (siccatives) based on cobalt and manganese. The compound contains neither conserving agents nor siccatives based on lead, barium, other dangerous heavy metals and other artificial substances
Thinning agent: Not applicable. In a case of thickening up, the compound should be mixed thoroughly and, if needed, warmed a little bit in a container with hot water (do not use heaters or gas-burners!).
Solids content: 99 to 100%.
Storage: It is supposed to be stored in a dry cool place in tightly closed packing under temperature not lower than +5°С and preferably not higher than +35°С. In a case of freezing down after a thorough mixing, a consistency and properties of the compound restore completely (the process accelerates in a case of the container warming with hot water).
Shelf life: Storage term in the original closed container is about 12 months.
Container volume: 0.5; 1; 2.5 and 10 l.
Class of hazard: Not applicable.
Density: 0.92 to 0.95 g/cm3.
Viscosity: ~60 to 65 sec (DIN-size beaker 4 mm).
Flash-point: Do not apply at more than 200°C.
Quantity used: For the first and second layers, 12 to 50 m2/l, for the last layer more than 100 m2/l depending on absorptiveness of the surface.
Drying time: Removing of a compound excess is to be done during 30 minutes after application process. The next layer application must be done in 24 hours. Final drying up takes place during 24 to 48 hours at temperature 20°C and humidity 50-60%.
Surface preparation: Remove an old film coat (if any). Clean the surface from dirt and grease (by washing up with water and soap) and dry up to the humidity level 14-15%. In dependence with wood kind and desirable smoothness, grind off the surface with abrasive means with grain P100-220 (it is recommended in average not less than P150-180), remove dust thoroughly. In a case of wood treatment in places of increased water action, it is recommended preliminary surface grounding with Oil primer with silver for antifungal wood protection No.11 according to the applicable instruction for use.
Application process: The surface must be dry; the recommended humidity is not more than 14 or 15%. It is recommended to conduct the treatment at temperature not less than +12 to +15°С. The compound is applied in 1 or 2 (sometimes in 3) layers. Mix the compound properly and apply it on the surface with a brush or a roller with short nap. Do it uniformly with some excess. On strongly soaking-in surfaces, repeatedly apply the oil onto those fields, where it has been soaked in already and do not wait of drying up of the rest of fields. During 30 minutes after the application, watch the behavior of oil soaking in on the surface and redistribute it between those fields, where it has been soaked in already, and those fields, where it has not been soaked yet. If the oil soaked in completely during 30 minutes, apply the next layer. After 30 minutes after the application of the last layer, remove an oil excess with aid of a cotton tissue. In 24 hours, it is possible to apply the second layer in the similar way. As a rule, application of 1 or 2 layers is enough. If needed (when higher wear resistance is required), it is possible to apply the third oil layer. Before the third layer application, the surface needs to be treated with a sandpaper P180-240. The third layer is apply very sparingly with a cotton brush or a polishing pad in the similar way as for the first and the second layers. Repeat the procedure of the third layer application up to oil soaking-in cease. Final drying up takes place in 24 to 48 hours. During 14 days, it is not recommended subjecting the cover to increased loads and moisture action.Above the final layer, not earlier than in 3 days, the layer of Carnauba wax, high gloss No.1090 can by apply.
Tinting: In the compound, dry pigments can be added in volume up to 30% For uniform mixing up it is recommended first to dilute a pigment in a small compound volume and then to mix up with the rest of the oil.
Cleaning and care: The surface can be wiped with a wet tissue. In a case of contamination, wash it up with warm water, into which non-abrasive non-alkaline detergent can be added. Or you can add Cleanser for floor No.5050 or locally apply more concentrated compound No.5050 (for use in case of a worse contamination). If the surface is worn-out, apply an oil thin layer on the worn-out field. In a case of a local damage (or contamination), the surface should be scraped with a sandpaper with small grain (for example P240) and then the treated field should be covered with the oil. For a better conservation of the silky gloss and fresh look of the surface, it is recommended wetting cleaning, namely wiping the surface with water, to 10 liters of which 1 or 2 tablespoons of the emulsion of carnauba palm wax No.1090 should be added. In a case of a significant contamination and exhaustion of a considerable surface part, conduct a complex cleaning up with aid of sponge or tissue or polishing machine (approximately once per 3 years depending on operation conditions).
Tool cleaning: Immediately after use it is needed to wash the tool with warm water with soap or detergent and to dry it up.
Utilization: An empty container must be utilized in accordance with regional legislation. Any dried up product remainders can be disposed together with domestic garbage.
Safety advice: To store in a childproof place. It is forbidden to pour remainders into sewage. In a case of contact with eyes, wash with a lot of water. Soaked with the product materials (tissues, dresses, sponges) and tools must be washed up with water and soap and dried up in a fireproof container or on a fireproof surface as during the drying up process, a hazard is present of a spontaneous combustion. After that the materials can be disposed together with common garbage.

The compound contains completely natural substances. That is why before its application it is necessary to ensure that you do not suffer from allergy to vegetable substances and products of beekeeping!