Natural as wood…

Austrian traditions of wood treatment


Environment
Friendliness and Care
head1

Protection and nature power

Garden wood oil with beeswax No.3010

For constructions being operated indoor, under an open shed or outdoor under action of atmospheric factors. A noble natural surface. Product with dry remainder 100%. Short drying up time.

Use
It is meant for structural elements, decorative elements, furniture, walls, doors, windows and other wooden objects including those being subjected to wear, operated anywhere: indoor, under an open shed and also outdoor in conditions of atmospheric factors action. The compound is not suitable for floors
Technical data sheet — PDF
Properties Directions for use
Gloss: Silky-semi-mat.
Color: Pale-strawy (natural). After several months the wood gets a nice honey-like tincture. The compound can be colored with dry pigments. For external treatment, one needs to use the compound only it its colored form. It is recommended using mineral pigments.
Complete composition: heat-polymerized mixture of linseed oil and wood oil; heat-polymerized castor oil; boiled down mixture of linseed oil, castor oil, wood oil and fatty acids from vegetable sources; heat-polymerized linseed oil; linseed oil; wood oil; beeswax; zinc oxide; fir needle oil; fast-drying materials based on cobalt (less than 0.01%) and manganese (less than 0.01%).
Content of artificial substances: The compound contains two artificial substances: they are fast-drying materials (siccatives) based on cobalt and manganese. The compound contains neither conserving agents nor siccatives based on lead, barium or other dangerous heavy metals and other artificial substances.
Thinning agent: not applicable. In a case of thickening up, the compound should be mixed thoroughly and, if needed, warmed a little bit in a container with hot water (do not use heaters or gas-burners!).
Solids content: 99 to 100%.
Storage: It is supposed to be stored in a dry cool place in tightly closed packing under temperature not lower than +5°С and preferably not higher than +35°С. In a case of freezing down after a thorough mixing, a consistency and properties of the compound restore completely (the process accelerates in a case of the container warming with hot water).
Shelf life: Storage term in the original closed container is about 12 months.
Container volume: 0.5; 1; 2.5 and 10 l.
Class of hazard: Not applicable.
Density: 0.92 to 0.95 g/cm3.
Viscosity: ~60 to 65 sec (DIN-size beaker 4 mm).
Flash-point: Do not apply at more than 200°C.
Quantity used: For the first and second layers, 25 to 50 m2/l depending on absorptiveness of the surface.
Drying time: Removing of a compound excess is to be done during 30 minutes after application process. The next layer application must be done in 24 hours. Final drying up takes place during 24 to 48 hours at temperature 20°C and humidity 50-60%.
Surface preparation: Remove an old film coat (if any). Clean the surface from dirt and grease (by washing up with water and soap) and dry up to the humidity level 14-15%. In dependence with wood kind and desirable smoothness, grind off the surface with abrasive means with grain P100-220 (it is recommended in average not less than P150-180), remove dust thoroughly.
Application process: The surface must be dry; the recommended humidity is not more than 14 or 15%. It is recommended to conduct the treatment at temperature not less than +15°С. The compound is applied in 1 or 2 (sometimes in 3) layers. Mix the compound properly and apply it on the surface with a brush or a roller with short nap. Do it uniformly with some excess. On strongly soaking-in surfaces, repeatedly apply the oil onto those fields, where it has been soaked-in already and do not wait of drying up of the rest of fields. During 30 minutes after the application, watch the behavior of oil soaking-in on the surface and redistribute it between those fields, where it has been soaked-in already, and those fields, where it has not been soaked yet. If the oil soaked-in completely during 30 minutes, apply the next layer. After 30 minutes after the application of the last layer, remove an oil excess with aid of a cotton tissue. In 24 hours, it is possible to apply the second layer in the similar way. As a rule, application of 1 or 2 layers is enough. If needed, it is possible to apply the third oil layer. Before the third layer application, the surface needs to be treated with a sandpaper P180-240. The third layer is apply very sparingly with a brush or a roller or a cotton tissue in the way similar to first and second layers application. Repeat the procedure of the third layer application up to oil soaking-in cease. Final drying up takes place in 24 to 48 hours.Above the final layer, not earlier than in 3 days, the layer of Carnauba wax, high gloss No.1090 can by apply.
Tinting: In the compound, dry pigments can be added in volume up to 30%. For uniform mixing up, it is recommended firstly to dilute a pigment in a small compound volume and then to mix up with the rest of compound.
Cleaning and care: The surface can be wiped with a wet tissue. In a case of contamination, wash it up with warm water, into which non-abrasive non-alkaline detergent can be added. If the surface is worn-out, apply an oil thin layer on the worn-out field. In a case of a local damage (or contamination), the surface should be scraped with a sandpaper with small grain (for example P240) and then the treated field should be covered with the oil. For a better conservation of the silky gloss and the fresh look of the surface, it is recommended wetting cleaning, namely wiping the surface with water, to 10 liters of which 1 or 2 tablespoons of the emulsion of carnauba palm wax No.1090 should be added.
Tool cleaning: Immediately after use it is needed to wash the tool with warm water with soap or detergent and to dry it up.
Utilization: An empty container must be utilized in accordance with regional legislation. Any dried up product remainders can be disposed together with domestic garbage.
Safety advice: To store in a childproof place. It is forbidden to pour remainders into sewage. In a case of contact with eyes, wash with a lot of water. Soaked with the product materials (tissues, dresses, sponges) and tools must be washed up with water and soap and dried up in a fireproof container or on a fireproof surface as during the drying up process, a hazard is present of a spontaneous combustion. After that the materials can be disposed together with common garbage.

The compound contains completely natural substances. That is why before its application it is necessary to ensure that you do not suffer from allergy to vegetable substances and products of beekeeping!