Natural as wood…

Austrian traditions of wood treatment

and Esthetics

Beauty and naturality

Hard oil for worktops No.1035


Protection against moisture and contamination; hardening and ennobling of surfaces subjected to a wear and a contact with food products. Contaminants are removed easily from a treated surface.

It suits perfectly for tabletops, cutting boards, window sills, handrails, toys and other wooden surfaces subjected to a wear as well as for furniture and wooden kitchen utensils.
Technical data sheet — PDF
Properties Directions for use
Gloss: Silky-semi-mat.
Color: In its liquid uncolored form, the compound is milky-white and after drying up it is transparent. After several months the wood acquires nice honey-like tincture. The compound can be colored with dry pigments.
Complete composition: water; heat-polymerized wood oil; boiled down mixture of linseed oil, castor oil, wood oil, resin of conifers and glycerin from vegetable sources; wax of carnauba palm; vegetable wetting agents; lecithin; natural silver in ultra-micro-dispersed form (nanoform) in traces.
Content of artificial substances: does not contain any artificial substances, fast-drying materials, conserving agents or heavy metals.
Thinning agent: Water.
Solids content: <100%.
Storage: It is supposed to be stored in a dry cool place in tightly closed packing under temperature not lower than +5°С and preferably not higher than +35°С. Do not freeze!
Shelf life: Storage term in the original closed container is about 12 months.
Container volume: 0.5; 1; 2.5 and 10 l.
Class of hazard: Not applicable.
Density: 0.99 to 1.02 g/cm3.
Viscosity: ~20 to 25 sec (DIN-size beaker 4 mm).
Flash-point: Do not apply at more than 200°C.
Quantity used: Approximately 8 to 12 m2/l for the first layer, 10 to 18 m2/l for the second layer and 20 to 30 m2/l for the third layer depending on absorptiveness of the surface.
Drying time: Approximately in 6 to 8 hours, it is possible to apply the second layer. In 8 to 24 hours after application of the second layer, it is possible to apply the third layer. Final drying up lasts 72 hours. Stable surface and water-repellent and mudguard properties forming takes place during 7 to 14 days & nights at temperature 20°C and humidity 50-60%.
Surface preparation: Remove an old film coat (if any). Clean the surface from dirt and grease (by washing up with water and soap) and dry up to the humidity level 14-15%. In dependence with a wood kind and a desirable smoothness, grind off the surface with abrasive means with grain P100-220 (it is recommended in average not less than P150-180), remove dust thoroughly.
Application process: The surface must be dry; the recommended humidity is not more than 14 or 15%. It is recommended to conduct the treatment at temperature not less than +12 to +15°С. Mix the compound properly and apply it on the surface with an excess along grain. You can do it with a brush, a roller with synthetic nap, a spray gun or by dipping. In 30 to 40 minutes the compound excess must be rubbed into and then removed from the surface with aid of lint-free tissue. In 6 to 8 hours, the raised nap can be removed by a sandpaper sheet with grain P240. The second layer should be applied in similar way. If necessary, in 6 to 8 hours, application process third layer is possible. Final drying up lasts 48 to 72 hours. Stable surface and water-repellent and mudguard properties forming takes place during 7 to 14 days & nights at temperature 20°C and humidity 50-60%. Above the final layer, not earlier than in 3 days, the layer of Carnauba wax, high gloss No.1090 can by apply.
Tinting: Into the compound, dry pigments can be added in volume up to 30% or universal pastes or aqueous coloring pastes in volume recommended by a paste producer. Before pastes adding, pay attention to their composition and environmental friendliness; for greater security, add natural dry pigments. For uniform mixing up it is recommended first to dilute a pigment in a small compound volume of No.1035 and then to mix up with the rest of compound.
Cleaning and care: The surface can be wiped with a wet tissue. In a case of contamination, wash it up with warm water with soap. If the surface is worn-out, apply a compound thin layer on the worn-out field. For better conservation of the silky gloss and fresh look of the surface, it is recommended wetting cleaning, namely wiping the surface with water, to 10 liters of which 1 or 2 tablespoons of the emulsion of carnauba palm wax No.1090 should be added.
Tool cleaning: Immediately after use it is needed to wash the tool with warm water with soap or detergent and to dry it up.
Utilization: An empty container must be utilized in accordance with regional legislation. Any dried up product remainders can be disposed together with domestic garbage.
Safety advice: To store in a childproof place. It is forbidden to pour remainders into sewage. In a case of contact with eyes, wash them with a lot of water. Soaked with the product materials (tissues, dresses, sponges) and tools must be washed up with water and soap and dried up in a fireproof container or on a fireproof surface as during the drying up process, a hazard is present of a spontaneous combustion. After that the materials can be disposed together with common garbage.

The compound contains completely natural substances. That is why before its application it is necessary to ensure that you do not suffer from allergy to vegetable substances and products of beekeeping!